Search results

Two options; save your current map to PC and load a zero map. This passes through the OEM ECU inputs and your MPGs should near the old ###. On the FZ6, all inputs are passthough and one can simply unplug the FC from the Injectors and Plug the Injectors back into the OEM ECU. Again, MPG should...

Thanks Dennis! Always appreciated! Any chance of getting the Thanks and Like buttons working?

Everything shared points to cable failure. I would be ordering a new one as this one is likely fraying and about to snap. Loosen the adjuster completely and disconnect the cable from the perch. Then bend the tab on engines lever side up and disconnect the cable end from the lever. Pull the...

Does this version of PC retain the O2 sensor?

You need to be very selective in receiver choices as not all class 3 receivers are rated for the same load or tongue weight. In each class, 3, 4, and 5 there are different load carrying abilities. Be sure to verify exactly what have so nothing bad happens. The minimum is a class 3 with weight...

Check this one out 1997 to 2007! 4TV-14602-00-00 YAMAHA EXHAUST PIPE COMP.

This is so you can do your own thing but use the where used function on these sites. Keep in mind that color changes can make a new part number! 5SL-14602-00-00 YAMAHA EXHAUST PIPE COMP.

FWIW the main reason AIS blocking plates are installed is to get a proper O2 reading when on the dyno and/or using an O2 data logger as the added air fouls up testing making it look lean when it is not.

Agreed, likely a loose connection. You might stick volt meter on the battery at each state; Off for two hours or more: 12.85 to 13.00v Idle: 13 but very dependent on batt state i.e. fully charged? 2500 RPM: 14 - 14.5 5000 RPM: 14 - 14.5 The reason is although the bike may run voltages over...

Excellent! You get the gauge working too? If not, Pop the connector apart and examine the wires.

Any chance the wires were strained? They are the weakest link and more often than not, they get stretched beyond their means. Although the connector "green one" on the fz6 has power, if it is damaged and only has a few strands left, it can show voltage but lack the current carrying capacity...

Clean it off. See if it repeats. If it gets bouncy, time to upgrade...

Follow that link and the picture is there. That model has the relay, a short lead, and plug. The OEM FZ6 was one piece. Both mount the same and connect the same and yes, they are 2 prong, 2 post, 2 conductor, 2 wire.... whatever you want to call it. It's here on the right side.

FZ6 is 2 wire. The R IDK but 99% certain its the same. This is on the other forum... $9.oo Electronic Flasher Relays-Great Price!

Are both the FZ and the R 105/105 stock? Its been too long.

Take a peak at this... I4 DOHC from a cage - notice the slotted cam gears? Apply this same concept here but in this case, you or the machine shop slots the existing holes to obtain the LC desired. By slotting the existing holes it allows you to change the lobe center in relation to crankshaft /...

Rep points works but ya, Thanks and Like are busted from Android 7.0... Thanks for keeping the forum up and running Dennis!!

Risk vs reward comes to mind.... Be safe! Blocking under the header is a safe bet but a bit more work...

Curious, why not use the IACV assembly? Its simple, effective, and it works. Granted it wants hot water for a warm idle but that can be over ridden as it unbolts. Because those venturi's have no provissions for idle air I am wondering what your plan is. Good luck!

Sounds like a fun project! My reference is stock S2 07-09 FZ6 ecu... so apples and oranges. It seems like a must have to me but vacuum is the only measure of load imposed. So that, TPS, CPS, and cylinder head temp would make up the vitals. Oil temp takes to long to come around in most where the...